The decoration of the house requires a lot of attention, but the decoration of the factory also needs our attention. There are many places that we need to know in advance. How to construct it? What are the main points of the renovation of the Songjiang plant ? If you want to know, let's take a look at the small series of the decoration home network. First, how to construct Songjiang plant decoration 1. Design of automatic fire protection facilities The clean factory decoration is to prevent dust from scattering. The air purification generally adopts the ventilation mode of sending up or down or horizontal forced air supply. Its return air is often placed at the ground, which makes the air purification system not stop working in the early stage of the fire. In the case, the common smoke detector installed on the ceiling is used to detect the fire signal, and the early warning effect is often not obtained. Therefore, for the selection of fire alarm system detectors, it is not suitable for smoke detectors. If it is necessary, the installation method and installation location of the smoke detector should be reasonably designed. 2. Design the layout of the plant Before the construction of the plant, the internal unit layout of the plant shall be demonstrated by the design unit, construction unit, user unit, equipment installation or supply unit. First of all, it should be considered to place the flammable and explosive process or equipment as far as possible outside the factory or adjacent to the factory. If there are difficulties or process needs must be placed in the factory, it should be set up by the external wall and other functional areas of the plant. Separated by solid walls to facilitate fire and explosion protection. Secondly, the exterior wall of the intensive part of the assembly workshop, packaging workshop, etc. will be ensured, and a long side will be the outer wall of the factory. On the one hand, it is convenient to open an emergency evacuation exit, and on the other hand, it is convenient for smoke evacuation and rescue during an accident. Second, Songjiang plant decoration points 1. The wall and ceiling of the factory technical interlayer should be plastered. Chengdu factory decoration Xiaobian feels that if you need to replace the high-efficiency air filter in the technical interlayer, it is necessary to increase the paint finish. The ground, return air trench and technical interlayer located underground shall be waterproof or moisture proof and mildew proof. The interior surface decoration standards of the building air duct and the return air trench should be compatible with the entire air supply and return air system, and should be easy to remove dust. 2. The details to be paid attention to in the decoration of the factory building is to evaluate the ground, because the ground must be kept flat during the decoration of the factory. If the unevenness will have a certain impact on the future plant, if there is unevenness, it should be timely 1:3 cement. It is also possible to flatten the mortar or directly pave it with cement. 3. If there is some new space in the indoor compartment, according to the fire protection regulations, it is necessary to add an independent smoke detector, and it is necessary to ask the professional factory decoration company to do the fire protection. Usually the maintenance unit of the building, if this detail and the details of the second article have not been changed, it is not acceptable for the property. There are a lot of people who don't know much about the decoration of the factory. But if you want to know the relevant knowledge of the decoration of the factory, then how do you construct and decorate the decoration of the Songjiang plant? I think everyone has read the introduction of the above series. I understand that, if you still want to know more about decoration, please continue to pay attention to the decoration home Internet cafe. More related wonderful reading: Industrial plant renovation steps, industrial plant decoration precautions Plant decoration design considerations plant decoration design steps Factory decoration main points How to decorate industrial plants? Industrial plant decoration precautions How to decorate the factory? Factory renovation process Diamond Wire For Silicon Cutting
The advantages of Diamond Wire cutting
technology are huge, and it can replace the traditional mortar wire. Diamond
wire is mainly used in the cutting of hard and brittle materials such as
crystalline silicon and sapphire. Compared with traditional mortar steel wire
cutting, it has high efficiency (4-5 times the cutting speed), less loss and
high chip yield (15-20% more silicon). The advantages of low environmental
pollution (no organic liquid) and high product quality. Among the diamond wire,
electroplated diamond wire is widely favored by the market for its outstanding
advantages of low wire consumption per piece, small wire diameter and high
cutting efficiency, and is superior to resin diamond wire.
Diamond Wire For Silicon Cutting,Silicon Cutting,Diamond Wire For Silicon,Diamond Wire Sawing For Silicon Jiangyin Baoneng Precision New Material Co.,LTD , https://www.baonengwire.com
