Blisting method After picking the tender leaves, wash them with water, put them into the tank or cement pool, use 80%~100% warm water to heat them, then put them in clean water for 2 hours~4 hours. The amount of water is generally exceeded. The noodles can be used. When soaking apricot leaves, peach leaves, willow leaves and mulberry leaves, it is necessary to change the water several times to remove the bitterness. After soaking the soaked leaves, they can be mixed into the diet to feed the pigs. Drying method The picked leaves are dried or dried, and after being crushed, they can be directly mixed into the feed for feeding. Such as locust leaves, mulberry leaves, poplar leaves and some fruit leaves, etc., the feeding amount is generally controlled at 5% to 10% of the total amount of the diet. Salt method Wash and chop the leaves, pour into the tank or in the cement pool, take the salt according to the amount of 5%, and layer the leaves with a layer of salt to make salt. After salting, the leaves are not easy to rot, have a fresh fragrance, and have good palatability. Silage method Wash the leaves, chop them, drain the water, and then put them into the silage container layer by layer. If the water content in the leaves is too much, add 10% of the gluten to the mixed silage. When the water content is low, , can be adjusted by manual water spray. Fermentation The harvested leaves or the collected autumn natural leaves are dried and processed into pulverized leaves. Adjust the old dough for 2 kg of noodles into a thin paste with a proper amount of water, add 5 kg of cornmeal and 10 kg of rice bran, mix well, stir into a thick paste, and let it ferment for 24 hours. Then add 50 kilograms of leaf powder and 10 kilograms of distiller's grains, stir well, the humidity is held in groups by hand, and it is advisable to see the water drops in the hand, then put it into the fermentation tank or the pool, and then install it immediately, and then cover it to cover it. The material is covered with a cylinder (pool) and the temperature is kept at 30 ° C ~ 50 ° C. It can be taken after 48 hours of fermentation.
About high speed Door Accessories:
1.Driving system: High Speed Door Servo System motor and control, motor SNMA / SEJ +reducer+flang+encoder+control box
2.Other accessories: Middle aluminium bar, bottom aluminium bar, aluminium vertical track, stainless steel vertical track, brushes,round nylon strip, PVC roll, rolling steel tube complete, drum be;;s for rolling tube, side end covers, stainless steel cover, steel tubes, air bag sensor system, safety light beam, Microwave sensor 24 Gigahertz,PVC welding machine, smoke and fire sensors, PVC transparent window, magnetic loop, photocell, remote control, manual push button, sound warning alarm Led lamp traffic light
For some main accessories, here is detain introduction:
1).24G radar sensor:
Brand: Hofic
Technology: Microwave processor
Maintain time: 0.5s
Protection: IP54
Transmitting frequency: 24.125GHz
Maximum installation height: <5meter
Transmitting power density: <5mw/cm2
Power consumption: <1W(VA)
Installation angle: 0-90°(lengthways) -30-30°(crosswise)
Supply voltage: AC&DC 12V-30V
2).Photocell:
Approval CE & ISO9001
Power supply AC/DC 12-30V
Static current 25A
Action current 40mA
Mounting distance Max 10m
NO or NC contact Done by NO./NC. contact selection
Working environment temperature -42℃ to +45℃
Working environment humidity 10 to 90%RH
Appearance dimensions( controller) 123*50*32mm(L*W*H)
Appearance dimensions(Magic eye head) 19*13mm(L*D)
3). Remote control
Operating Voltage: AC220V/50HZ+-20%
Transmit power:≤100mW;Super regenerative module, strong anti-interference
Operating temperature:-30℃-+70℃
Working frequency: 433MHZ;transmitter 1527, millions of encoding chip
Accept sensitivity:≤110dB
Manipulation method: electric remote control
Configure the quantity: Wireless number; factory configuration transmitter two. Can be equipped with PT2272 digital decoder chip
Configure the function: Up, down, stop, anti-lock full-featured reproduction
4). Magnetic loop
Voltage: 12V AC/DC +-10% 24V 115V AC+-10% 230V
Power: <2VA
Continued electrical output: 7A / 250V AC
Frequency range: 20 to 200K Hz
Response time: infinity (factory setting) or adjust maintain time
Sensitivity: 0.01% to 0.1% divided into 3 levels
Protection level: IP30
Electromagnetic compatibility (EMC) Complies with EM50081-1 and EN50082-2
Detection loop inductance: the limit of 40uH to 100uH ideal value 80uH to 300uH
Operating temperature: -25 ℃ to 70 ℃
Storage temperature: -40 ℃ to 85 ℃
Relative humidity: <90% non-condensing
Temperature compensation: automatic compensation up to 50 ℃ / h
Connection type: 11 pin DIN rail socket
Dimensions: 41 * 78 * 85 mm (width * height * length)
Weight: 250 grams
5). manual push button
This exit switch button is made of ABS and has built-in indicator light make it looks more elegant and fashionbale. It can be widely used in public entrance gates, public door, home, office, hotel, etc.
Door Exit Button Push To Exit Switch Door Opener For Access Control Security
Main Feature
Fashionable appearance
Made of ABS Plastic
Easy to install and operate
Used for access control
Specification
Mechanical Life: 500,000 test
Material: Plastic
6). Limit switch encoder
Voltage: DC5V-24V
Output voltage: high voltage≥85%Vcc, low voltage≤0.5V
Maximum mechanical speed:6000rpm
Anti-vibration: 50m/s,10-200HZ,XYZeach way 2 times.
Current consumption:≤30mA
Response frequency: 0-100KHZ
Protection: waterproof,oil proof,dust prevention, IP54
The output code system: binary code
Operating life: MTBF≥30000(+25℃,2000rpm)
Rotational inertia:4.0x10-8kgm²
Maximum load:radial direction20N
Axial direction:10N
Weight: about 0.4kg
High Speed Door Accessories,High Speed Door,Electronic High Speed Door Accessories Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfhighspeeddoor.com
Pig leaf feed processing modulation method
Many leaves are rich in plant protein and a variety of nutrients needed for pig growth and development, and can be used as pig feed. There are many leaves in nature that can be used as pig feed. Commonly used are locust leaves, poplar leaves, willow leaves, eucalyptus leaves, mulberry leaves, camphor leaves, pine needles, apple leaves, pear leaves, mountain leaves, apricot leaves, peach leaves, Grape leaves, persimmon leaves, jujube leaves, etc. In addition, the hedgehog and poplar flowers are good feeds for pigs. The leaves used as feed are scientifically processed to not only improve their palatability, but also have a significant effect on improving the utilization rate, digestibility and nutritional value of the leaves. Several commonly used simple processing modulation methods for leaf feed are now introduced.