Baseboard installation stainless steel angle valve stainless steel flange stainless steel double open door stainless steel bathroom Conveyor Chain ,Overhead Conveyor Chain,Heavy Duty Conveyor Chain,Single Conveyor Chain NINGBO DEMY (D&M) BEARINGS CO.,LTD , https://www.demybmtbearing.com
[Stainless steel baseboard construction steps]
First, the preparation work 1, the production of positioning ruler: When installing the buckle, use the positioning ruler to determine the height of the buckle installation position. Positioning ruler length 1000-2400 mm; width 40-50 mm; height according to the skirting line model, T70 high 17-17.75 mm; T80 high 14.5-15 mm; T100 high 38-38.5 mm; T110 high 36.5-37 mm; the positioning rule can be made of wood or iron.
2. Clean up the wall base: Remove the cement floating blocks protruding from the walls, corners, and the roots of the baseboard where the skirting line is installed; check the straightness of the walls and the maximum gap is no more than 3 mm. No side, the wall should be flattened. The wall recesses should be shimmed.
Second, the installation of buckles 1, installation method (fixed cement row nails): The buckle on the positioning ruler, against the wall roots, press the upper end of the buckle under the fingers, with a nail gun fixed, see Figure 1. The cement row nails are 32 mm long; the snap spacing is about 400 mm; there is a snap on the two baseboard connectors; there must be one snap on each wall end about 30 mm.
2. Installation method 2 (impact drill drilling and fixing): Fix a drilling die (drill hole diameter is slightly larger than the impact drill bit) on the positioning ruler, resist the wall root, drill with the impact drill on the wall, and insert in the hole. Wooden needle or plastic expansion tube. When fixing the buckle, you still need to use the positioning rule to fix the buckle at the same height (using the waist hole on the buckle). The rest are the same as above.
3, Description: wooden wall or plasterboard wall with a woodworking nail gun to fix the buckle; plaster wall can also use light steel keel with self-tapping screws to fix the buckle.
Third, install skirting profiles 
1. After ensuring that all the snaps have been installed on the same straight line (with an error of ±1.5 mm), cut the yin and yang angles according to the size and leave 2 mm or so for the seam of the silicone to grind the burrs. Then tear off the protective film under the baseboard to seal with silicone. Neutral silica gel for sealing and mud seams, the color of which is usually silver gray or white.
2. Lay the bottom of the baseboard with a good size in a semi-hook on the top of the buckle, and then lift the bottom of the baseboard upwards and then press the wall down to make the top buckle of the buckle completely enter the kicking foot. The upper part of the groove, while tapping the middle of the baseboard, see Figure 2. When installing, start from one end, and one snapping one buckle into the other stepwise, avoid hammering.
3. After the installation, the gap between the baseboard and the wall and the ground shall be sealed with silicone, and the yin and yang angles and the reserved 2 mm gap shall be used to apply silicone paste.
4. Tear off all the protective film on the baseboard and wipe the stainless steel veneer residue with the old powder. Remove the black spots formed by the heat of the glue at the incision with the wire cloth. 
5, the use of stainless steel Yin Yang angle is more convenient to install, welcome customers to choose. The installation method: After the baseboard is installed, use AB glue to stick the inside corner, the outside corner, and the sealing head to the joint.
Xiao Bian concludes: On the stainless steel baseboard construction process for everyone to introduce here. In addition to its protective function, the baseboard now has become a kind of material that can reflect the decorative style and deserves attention. Exquisite baseboards can often play the role of four or two, adding a lot to your home. For more relevant knowledge, please continue to pay attention to this website information platform.
Stainless steel baseboard construction process how to install baseboard
The stainless steel baseboard is made of stainless steel panel and high-strength lining. The outer layer is a matt frosted stainless steel plate. The inner lining is made of wood-plastic material. It does not need to use a thin wood to make the bottom, and it is buckled directly. The installation is very convenient. Next, Xiaobian will introduce stainless steel skirting construction technology to everyone.