February 22, 2025

Talking about the characteristics of various drying equipment - fluidized bed drying equipment

In the last issue, we introduced the drying characteristics of spray drying equipment . Today we will introduce the drying characteristics of fluidized bed drying equipment. These important foundations must be understood and learned by each user. Only the characteristics of each drying equipment can be truly understood. In order to better use, improve the utilization rate and application ability of drying equipment, and reduce the wrong operation in use. The following is a detailed introduction to the drying characteristics of the fluidized bed drying equipment.
I. Overview of the drying process of fluidized bed drying equipment Fluidized bed drying equipment, also known as fluidized bed drying equipment, the drying characteristics of the drying equipment, the granular solid materials are added to the fluidized bed drying equipment by a rotary feeder, and the air has a blower. It is sent to the combustion chamber, heated and sent to the bottom of the fluidized bed to be distributed and solid material is released to form a fluidized state, and the heat and mass exchange of the gas-solid phase is achieved. After the material is dried, it is sent out from the discharge port. The exhaust gas is discharged from the top of the fluidized bed and recovered by the cyclone collector. The product that is taken out is then evacuated after passing through the scrubber and the mist separator.
Second, the characteristics of fluidized bed drying equipment Fluidized bed drying equipment has the following specific characteristics, the drying equipment is suitable for the drying of non-agglomerating granular materials, the particle diameter can be from 30um-6um; the drying equipment has a simple structure, production The capacity is from tens of kilograms per hour to 400,000 kilograms per hour; the thermal efficiency is about 70%. When removing the combined moisture in the material, the thermal efficiency is about 30%-50%, and the volumetric heat transfer coefficient can reach 2326-6978W/( m?.°C); the residence time of the material in the fluidized bed is related to the structure of the fluidized bed. If the design is reasonable, the residence time of the material in the fluidized bed can be arbitrarily prolonged. The disadvantage is that the resistance of the hot air through the distribution plate and the material layer is relatively large, generally about 490-1470 Pa. The energy consumption of the blower is large. The material of the single-layer fluidized bed drying equipment is completely mixed in the fluidized bed, and some materials may go shortly and directly fly to the outlet from the feeding port to the discharging port, resulting in uneven drying of the materials. In order to improve the uniformity of drying of the materials in the fluidized bed, fluidized beds of different structures are generally used. Such as a single-layer fluidized bed with a baffle structure for controlling material short-circuit, a horizontal multi-chamber fluidized bed, a multi-layer fluidized bed, and the like.
The multi-layer fluidized bed drying device can increase the drying time of the material and improve the uniformity of the water content of the dried product, thereby facilitating the control of the dry quality of the product. However, as the number of layers increases in the multi-layer fluidized bed drying apparatus, the distribution plate increases correspondingly, and the bed resistance increases. At the same time, between the layers, the material should be quantitatively transferred from the upper layer to the lower layer, and to ensure a stable vulcanization state, an overflow device must be used. This in turn increases the complexity of the device structure. For the removal of moisture-bound materials, it is appropriate to use a multi-layer fluidized bed. For example, some large-scale pharmaceutical plants use a two-layer fluidized bed drying facility to dry the materials, and dry the aminopenin with a moisture content of 15%-30%. Some polyester textile mills use a five-layer fluidized bed drying equipment. The material is dried and the polyester resin is dried to make the moisture content of the product reach about 0.03%.
The horizontal multi-chamber fluidized bed drying equipment can adjust the air volume of each chamber by dividing into multiple chambers. At the same time, the baffle is added in the fluidized bed to avoid short-circuiting of the materials, and the moisture content of the dried product is relatively uniform. If the air volume and temperature of each room are adjusted in operation, or the hot air of the last few chambers is used once, or an internal heater is added, the thermal efficiency can be improved.
Through this introduction, we have a new understanding and understanding of fluidized bed drying equipment, which can increase the unnecessary waste of resources and low product quality in the use of fluidized bed drying equipment. 'Talk about the characteristics of various drying equipment - fluidized bed drying equipment

Stainless Steel Sliding Door

Characteristics and Advantages

(1) Intelligent control design: adjustable main parameter and secondary parameter automatically according to the weight of door leaves;

(2) Low noise: Special static sound track, integration of motor, worm-gear and retarder.

(3) Anti-clamping function: automatically reverse when meeting barriers;

(4) Unique electronic motor lock: the motor will lock up when the door is forced to open.(controlled by remote or switch)

(5) Tighten force: seal door when closed, power consumption approximately 10W under standby;

(6) Advanced brushless motor(36V,100W) can automatically adopt different heavy door leaves;

(7) Bi-doors inter-locking: one of the door leaves always remains closing;

(8)Safety sensor terminal: sensor stops working when door closed;

(9)Unique coating technology: never rusty;

(10)Easy and convenient to install;

(11)Working Process: when the door leaf closes to the right place, the door leaf will slightly shift to the door frame and the ground. The rubbers on the four sides of the door leaf will completely combine with door frame and ground, which ensures air tightness. When the door is open, the rubbers will separate from door frame and ground, which avoids contraction on the ground.

Technical Specification

Specification

Light Duty

Heavy Duty

Rang of the Door

Single-Leaf

Double-Leaf

Single-Leaf

Double-Leaf

Door leaf max weight

100kg

100kg x 2

200kg

200kg x 2

Mounting Method

Surface mounting or built-in mounting

Open Width

700-2000mm

650-2000mm

750-2000mm

650-2000mm

Power Supply

AC 220v ± 10%, 50-60 Hz

Opening Speed

300-500mm/s (adjustable)

Closing Speed

250-550mm/s (adjustable)

Creep speed

30-100mm/s (adjustable)

Hold-open time

0.5-20s (adjustable)

Airproof Force (Max.)

>70N

Manual Pushing Force

<100N

Electronic Lock Force

>800N

Power consumption

150W

Ambient temperature

-20+50 C

Technical Details:

(1) Rubber lining sealing technology combined with V groove on the guide rail enables the door completely sealed when the door closed;

(2)Special door body location technology. Semicircular surface beam on the ground matches with the V style groove at the bottom of door leaf, which stop the door from swing and make sure it moves stable and smooth;

(3) The door body decorated with matte stainless steel or spray surface, and on the middle and both sides with sealing stripes to ensure the hermetic effect.

(4)Feet sensor switch applied to avoid contagion;

Stainless Steel Sliding Door,Stainless Steel Bypass Sliding Door,Stainless Steel Interior Sliding Door,Stainless Steel Folding Sliding Door

Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffastdoor.com