Zhejiang Sealand Technology Co., Ltd.is a trustworthy supplier of Oil Mass Flow Meter, Oil Mass Flowmeter, Oil Coriolis Flow Meter, Oil Coriolis Flowmeter, Oil Coriolis Flow Meter, ATEX, IECEx & CE approved.
Operating Environment
Atmospheric pressure: 85kPa~106kPa
Ambient temp.: Refer to Chapter 1.6
Relative humidity: 5%~95%, non condensing
Operating conditions
Fluid: Liquid/Gas
Nominal pressure: 4MPa or 25MPa (Customizable)
Supply voltage: AC 85~265VAC, 50/60Hz or DC 12~24VDC(±5%), 5W
Outputs: Pulse 0~10KHz, RS-485, 4-20mA & HART (optional)
The meter consists of mass flow sensor and transmitter. Mass flow sensor is a phase-sensitive resonant sensor based on Coriolis effect, composed
of vibration tube, signal detector, concussion driver, structural support, shell, etc.
Mass flow transmitter is a micro-programming-centered electronic system, which supplies
thrust to sensor, transforms sensor signal into mass flow signal & others, and improves
accuracy in accordance with temperature parameter.
Oil Mass Flow Meter, Oil Mass Flowmeter, Oil Coriolis Flow Meter, Oil Coriolis Flowmeter, Oil Coriolis Flow Meter Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeter.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge> Tips for keeping the engine Tips for keeping the engine
Keep the engine tips.. /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
The use of magnets saw a trick in the car show; and was recognized by professional and technical personnel:
Use the NdFeB magnet in the general waste computer (the characteristic is the volume. The judgment of the 盘 盘 蛘哂 蛘哂 蛘哂 蛘哂 蛘哂 鹘 Π螅┰诨 Π螅┰诨 Π螅┰诨 Π螅┰诨 è¿¤éƒ è¿¤éƒ è¿¤éƒ é… é… é… é… é… é… é… é… é… é… é… é… é… é… é… é… é… æ¤ æ¤Southern feelings 鹗舴勰┪ 鹗舴勰┪ 诼 诼 诼 è¿¤é«‚è¯’è° æ·® æ·® æ·® æ·® æ·® æ·® æ·® æ·® æ·® æ·® æ·® ã— ã—
Pay attention to: the magnet inside the speaker of the general sound; not suitable for use.
Metal particles with large particle size and high hardness are one of the most important hazards of damage to the engine; it is scratching the cylinder wall, causing the addition of metal oxides in the oil; then inducing the oxidation of the oil and the acidity and corrosive addition of the first evil. The lime gravel is another Important scourge; the dust can be used for the dust and gravel; and the oil filter and air filter must be replaced by good quality.
For metal particles with large particle size and high hardness; you can use a strong magnet to suck on the oil filter; one to suck the metal residue; the second to magnetize the oil, there is no advantage; The return magnet in the hard disk; the magnetic strength of the magnet is strong, and the oil is changed every time; the withdrawal can not be removed. The following is the principle:
The machine filter itself is the collection of oil pollution and sanitary filtration; the oil pan of the oil pan also has a magnet; (many novices simply lose this magnetic core) but the magnetic is weak; nevertheless; I am 3,000 km of running-in period to protect the waste machine oil At the same time, I also saw a lot of metal particles accumulating above. At that time, the idea of ​​using a strong magnet placed on the filter to adsorb metal particles occurred. When the filter was changed, these things were thrown away with the old machine filter. After consideration; It is considered feasible and safe. The oil drain screw also has a magnet; and inside the machine head; the strong magnet is placed outside the filter housing; the sucking fine iron filings are also deposited in the machine filter; it is where it should be. Change the oil separately; that is, throw it away with the old machine filter. The strong magnet should be selected to have a large volume and small magnetic field, and the return magnet in the used hard disk; the magnetic strength of the magnet is satisfactory. If it is too large, it is easy to block the filter, diameter Within 2cm is appropriate.
Recommend to friends comments close window Bearing related knowledge The correct application of the spindle bearing method The single-row angular touch ball bearing layout type analysis of the quality requirements and disadvantages of the slewing bearing device and the protective bearing steel (3)
Analysis of bearing anomalies and causes
This article links to http://
Please indicate the bearing network http://
Previous:What problems should be paid attention to in bearing storage? The following series: Features of bimetal bearing housing and JBD
Fluid temperature: -200°C~+200°C (higher temp. model is customizable)
It`s composed of switching power supplier, guard grating, core processor board, display
module, etc., installed in a ex-proof junction box. Switching power supply offers power for
transmitter; safe grating isolates sensor and transmitter intrinsically; core processor detects
& processes sensor phase signal, sends mass flow signal and process communication.
Tips for keeping the engine
Source: China Bearing Network Time: 2014-09-25