>>> Related Links: Preparation for Pasting Wallpaper before Construction Tailoring of wallpaper First, according to the label paper in the paper roll package, the received goods are inspected to confirm whether the product model is correct and whether the production batch number is consistent. Usually, the cutting length of the wallpaper tape should be 5 to 10 cm in the height of the wall surface. When cropping, please pay attention to the pattern of flowers. Mark up and down and sequential numbers on the back of the trimmed tape. No need to spend: do not take into account the flower factor, just according to the wall height plus margin trimming. Flush on flowers: Patterns on different wallpaper strips are at the same height. First, cut the first wallpaper strip according to the height of the wall surface, and just trim the other strips by paying attention to the same pattern at the same height. Displacement vs. Flower: The same pattern on two adjacent wallpaper strips is not at the same height, and the amount of displacement is the amount of misalignment indicated on the label sheet. First trim the first wallpaper strip according to the wall height plus margin, and when cropping the second strip, first align the pattern with the same pattern on the first strip to determine a fiducial point and position the fiducial point from the fiducial point. The two tapes can be trimmed after being shifted by one misalignment amount. The same pattern of the third tape and the first tape should be at the same height, the same pattern of the second tape and the fourth tape at the same height, the same pattern on the single wallpaper tape at the same height The same pattern on the double-numbered wallpaper strip is also at the same height. When you need more than 2 rolls of wallpaper, to reduce scraps, you can use the first roll to cut out the number of wallpaper strips, and use the second roll to cut the number of wallpaper strips. Invert Paste: In order to balance the chromatic aberration of the tiny side of the wallpaper, the wallpaper may be marked with inverted glyphs on the label paper. The method of cutting the wallpaper tape is not exactly the same as that of the wallpaper of the flower. Only when the tape is pasted, every other tape needs to be inverted (after rotating 180 degrees) and then pasted. Blending glue Mixing glue requires a plastic tube (preferably with a scale) and a stirring bar. Add the appropriate amount of cold water according to the instructions on the powder package. Stir the water in one direction with a stirring stick and keep it in motion. In the state, continue to stir, and gradually add the powder to the water until the glue is in a uniform state. In principle, the heavier the wallpaper is, the smaller the amount of water added to the glue should be. According to the manufacturer's instructions on the powder packaging box, be sure to use clean cold water. Do not use warm water or hot water, or the glue will clump and cannot Mix well. The already mixed slurry can be diluted by adding water, and if the slurry is too thin, adding the powder in the stirred slurry will cause agglomeration and no further stirring. The glue should not be too thin, and the amount of glue should not be too thick, otherwise the glue can easily overflow from the seam and affect the quality of the paste. Wallpaper glue The non-woven fiber-backed wallpaper can be used to glue the glue on the back of the wallpaper, and the glue can be directly rolled on the wall surface. For other types of wallpapers, the glue must be applied to the back of the wallpaper. In order to ensure the construction quality as much as possible using a glue machine. If you use manual gluing, pay attention to the uniformity of the glue, and try to avoid spilling glue onto the surface of the wallpaper. Wallpaper dipping The correct dipping time plays a very important role in the final paste effect. After dipping, the wallpaper will swell 1% to 2% in the length direction and 1 centimeter in the width direction. Improper dipping time will cause the wallpaper to have bubbles, wrinkles, cracks in the joints, or dislocation of the pattern. Non-woven fiber-backed wallpaper can be pasted directly without using glue. Different wallpapers based on plain paper, such as pure paper wallpaper, glued wallpaper, and foamed wallpaper, need to be dipped for 8-10 minutes after the glue is applied. All the tapes must have the same dipped time. The specific operation is as follows: First, the glued wallpaper is folded in half. The upper half of the tape is folded in 2/3, and the center of the tape in the lower half of the tape is folded in 1/3. The right and left edges of the tape must be aligned during folding. After folding, use the fingers to gently knead the left and right edges of the tape to avoid opening. Otherwise, the glue on the edge of the tape will dry and cause cracking in the seam. The folded one-third of the fold is then folded back into the center and rolled into a tube. Avoid wallpaper crashes during folding and scrolling. Paste wallpaper The paste of the wallpaper is usually started from the window area. When pasting the first tape of each wall, be sure to draw a vertical line with a ruler or a plumb. After affixing the wallpaper to the wall, use wallpaper special rollers to roll out the bubbles in the same direction. Do not force the slurry out of the edge of the tape and spill it on the surface of the wallpaper. Use a scraper near the roof and the ground. Scrape, drive out the air bubbles and keep the wallpaper against the wall for a final cut. Do not use a scraper to scrape large areas on the wallpaper so as not to damage the surface of the wallpaper or to push part of the glue out of the edge of the wallpaper and spill it on the surface of the wallpaper, thus causing the wallpaper to be stuck loosely, cracks and dirt on the joints, etc. phenomenon. The seams at the edges of the two left and right tapes need to be rolled with beveled seam pressure rollers so that the wallpaper will be firmly bonded and the seams will not crack. If you accidentally spill the glue on the surface of the wallpaper, be sure to wipe it off with damp sponge immediately. Do not apply it back and forth. Otherwise, the wallpaper will leave a trace of white. Wall construction wallpaper window
There is a handle installed on the cabinet body in the
cabinet, which is called buckle free handle in the industry. The
aluminum alloy handle is directly installed on the cabinet body, so that
the door panel is clean without handle.
As
shown in the picture, the Black Buckle FREE handle is selected for the
floor cabinet, which is directly embedded into the cabinet body. The
exterior door panel has no raised handle, which is more neat. The handle of the hanging cabinet is directly hidden under the door panel and is not exposed outside. It looks cleaner.
Now let's see what this handle looks like? As shown below:
The
figure above shows the C-type buckle free handle, which is generally
used in the middle of the floor cabinet, drawer, bowl basket or hanging
cabinet. Available colors on the market are gun color, aluminum alloy natural color, or black, and aluminum alloy bright color.
G handle aluminium profile,aluminum cabinet handle,aluminum handle for kitchen cabinet,aluminium cabinet handle,Gola aluminum profile,aluminium gola profile
The
above figure is an L-shaped buckle free handle, which is generally used
above the cabinet floor to facilitate the opening of the door panel. colour
The figure above shows the special buckle free handle for the hanging
cabinet, which is specially installed on the bottom plate of the hanging
cabinet.
---------Dimension diagram of buckle free aluminum alloy handle---------------------------
After looking at the appearance of this handle, let's talk about its
installation method and the size of the handle: as shown in the figure
below
This is the first type. The aluminum alloy size of the conventional
circular arc cabinet is 20, the height of the middle type C is 70, the
depth is 23, the height of the floor cabinet L is 55, and the units
above the depth 23 {are mm}
This is the second kind. The right angle buckle free handle.
The aluminum alloy size of the hanging cabinet is 20 deep, the middle
C-type height is 73, and the depth is 26. The height of the L-type
cabinet is 57, and the depth is 26
-----------------------------------------------
Knowing the above dimensions, we will find that the dimensions of the
handle are different. Therefore, during processing and production, we
need to determine the type and size of the handle before cutting the
cabinet.
----Explanation of buckle free handle mode for floor cabinet installation------------
A buckle free handle shall be installed above the floor cabinet, and
there shall be a 30 gap between the door panel and the table
The buckle free handle is installed and needs to be fixed with L-shaped angle iron and cabinet side plate
C-type buckle free handle shall be installed at the middle drawer of the floor cabinet
The
above is the schematic diagram of the cabinet body side plate notch and
the installation handle of the floor cabinet. It should be noted that
the aluminum alloy buckle needs to be fixed with L-shaped angle iron. If
there is a drawer in the middle, or the bowl basket needs to be notched
on the middle side plate, the lower door plate exceeds the buckle by
15, the middle buckle of the middle door plate cover is 15, and 30 needs
to be left between the two door plates. The distance between the uppermost door panel and the table top is also
reserved at 30, which is convenient for opening the door panel.
---Explanation of buckle free handle for hanging cabinet installation-------------------------
The buckle free handle of the hanging cabinet is installed on
the bottom plate of the hanging cabinet, and the bottom plate needs to
be retracted 22 in front
There is a swing door in the middle of the hanging cabinet,
which needs to be equipped with C-type buckle, and a 30 gap is reserved
between the door panels
The
above is the schematic diagram of buckle free handle for hanging
cabinet installation. In conventional installation, the front of the
hanging cabinet bottom plate is shortened by 22, and the aluminum alloy
handle is slotted. If there is an upturned door in the middle of the hanging cabinet, it
is necessary to leave a distance and install L-type handle or C-type
handle. Leave 30 gaps between door panels. The middle fixed laminate shall also be moved upward according to the size of the drawing. {note: the buckle in the middle of the conventional hanging cabinet
needs to open the gap on the side plate. If the side plate of the
hanging cabinet leaks, the gap will not be opened}
-------Precautions in design are as follows:-------------------------------------
Note 1: the exposed part of the ground cabinet needs a light
plate to cover the cabinet incision, and the ground cabinet brace needs
to be installed horizontally, so that the buckle free handle L-shaped
fixed angle iron can be installed on the side plate.
Corner treatment scheme of buckle free handle
The first scheme is recommended at the corner of the buckle
free handle. The price of the handle door panel is high, and the handle
is on the edge of the top door panel.
Note
2: since the buckle free handle is installed on the cabinet, the
cabinet price needs to be high when designing the bowl and basket
cabinet to avoid the plate hitting the buckle free handle as shown in
the above video. The cabinet body can be 700 high, including the table top, and the skirting leg can be set to 850 high floor cabinet.
---------Buckle FREE handles can also be used in other customized furniture
Gola System Aluminium Profile,Gola Handle Aluminium Profile,Aluminum Cabinet Handle,Aluminium Cabinet Handle GuangDong XinCheng Material CO.,LTD , https://www.xin-alu.com